diff options
Diffstat (limited to 'dma/nwl_defines.h')
| -rw-r--r-- | dma/nwl_defines.h | 145 |
1 files changed, 0 insertions, 145 deletions
diff --git a/dma/nwl_defines.h b/dma/nwl_defines.h deleted file mode 100644 index ce3b686..0000000 --- a/dma/nwl_defines.h +++ /dev/null @@ -1,145 +0,0 @@ -/** @name Buffer Descriptor offsets - * USR fields are defined by higher level IP. For example, checksum offload - * setup for EMAC type devices. The 1st 8 words are utilized by hardware. Any - * words after the 8th are for software use only. - * @{ - */ -#define DMA_BD_BUFL_STATUS_OFFSET 0x00 /**< Buffer length + status */ -#define DMA_BD_USRL_OFFSET 0x04 /**< User logic specific - LSBytes */ -#define DMA_BD_USRH_OFFSET 0x08 /**< User logic specific - MSBytes */ -#define DMA_BD_CARDA_OFFSET 0x0C /**< Card address */ -#define DMA_BD_BUFL_CTRL_OFFSET 0x10 /**< Buffer length + control */ -#define DMA_BD_BUFAL_OFFSET 0x14 /**< Buffer address LSBytes */ -#define DMA_BD_BUFAH_OFFSET 0x18 /**< Buffer address MSBytes */ -#define DMA_BD_NDESC_OFFSET 0x1C /**< Next descriptor pointer */ - -/* Bit masks for some BD fields */ -#define DMA_BD_BUFL_MASK 0x000FFFFF /**< Byte count */ -#define DMA_BD_STATUS_MASK 0xFF000000 /**< Status Flags */ -#define DMA_BD_CTRL_MASK 0xFF000000 /**< Control Flags */ - -/* Bit masks for BD control field */ -#define DMA_BD_INT_ERROR_MASK 0x02000000 /**< Intr on error */ -#define DMA_BD_INT_COMP_MASK 0x01000000 /**< Intr on BD completion */ - -/* Bit masks for BD status field */ -#define DMA_BD_SOP_MASK 0x80000000 /**< Start of packet */ -#define DMA_BD_EOP_MASK 0x40000000 /**< End of packet */ -#define DMA_BD_ERROR_MASK 0x10000000 /**< BD had error */ -#define DMA_BD_USER_HIGH_ZERO_MASK 0x08000000 /**< User High Status zero */ -#define DMA_BD_USER_LOW_ZERO_MASK 0x04000000 /**< User Low Status zero */ -#define DMA_BD_SHORT_MASK 0x02000000 /**< BD not fully used */ -#define DMA_BD_COMP_MASK 0x01000000 /**< BD completed */ - - - -#define DMA_BD_MINIMUM_ALIGNMENT 0x40 /**< Minimum byte alignment */ - -/* Common DMA registers */ -#define REG_DMA_CTRL_STATUS 0x4000 /**< DMA Common Ctrl & Status */ - -/* These engine registers are applicable to both S2C and C2S channels. - * Register field mask and shift definitions are later in this file. - */ - -#define REG_DMA_ENG_CAP 0x00000000 /**< DMA Engine Capabilities */ -#define REG_DMA_ENG_CTRL_STATUS 0x00000004 /**< DMA Engine Control */ -#define REG_DMA_ENG_NEXT_BD 0x00000008 /**< HW Next desc pointer */ -#define REG_SW_NEXT_BD 0x0000000C /**< SW Next desc pointer */ -#define REG_DMA_ENG_LAST_BD 0x00000010 /**< HW Last completed pointer */ -#define REG_DMA_ENG_ACTIVE_TIME 0x00000014 /**< DMA Engine Active Time */ -#define REG_DMA_ENG_WAIT_TIME 0x00000018 /**< DMA Engine Wait Time */ -#define REG_DMA_ENG_COMP_BYTES 0x0000001C /**< DMA Engine Completed Bytes */ - -/* Register masks. The following constants define bit locations of various - * control bits in the registers. For further information on the meaning of - * the various bit masks, refer to the hardware spec. - * - * Masks have been written assuming HW bits 0-31 correspond to SW bits 0-31 - */ - -/** @name Bitmasks of REG_DMA_CTRL_STATUS register. - * @{ - */ -#define DMA_INT_ENABLE 0x00000001 /**< Enable global interrupts */ -#define DMA_INT_DISABLE 0x00000000 /**< Disable interrupts */ -#define DMA_INT_ACTIVE_MASK 0x00000002 /**< Interrupt active? */ -#define DMA_INT_PENDING_MASK 0x00000004 /**< Engine interrupt pending */ -#define DMA_INT_MSI_MODE 0x00000008 /**< MSI or Legacy mode? */ -#define DMA_USER_INT_ENABLE 0x00000010 /**< Enable user interrupts */ -#define DMA_USER_INT_ACTIVE_MASK 0x00000020 /**< Int - user interrupt */ -#define DMA_USER_INT_ACK 0x00000020 /**< Acknowledge */ -#define DMA_MPS_USED 0x00000700 /**< MPS Used */ -#define DMA_MRRS_USED 0x00007000 /**< MRRS Used */ -#define DMA_S2C_ENG_INT_VAL 0x00FF0000 /**< IRQ value of 1st 8 S2Cs */ -#define DMA_C2S_ENG_INT_VAL 0xFF000000 /**< IRQ value of 1st 8 C2Ss */ - -/** @name Bitmasks of REG_DMA_ENG_CAP register. - * @{ - */ -/* DMA engine characteristics */ -#define DMA_ENG_PRESENT_MASK 0x00000001 /**< DMA engine present? */ -#define DMA_ENG_DIRECTION_MASK 0x00000002 /**< DMA engine direction */ -#define DMA_ENG_C2S 0x00000002 /**< DMA engine - C2S */ -#define DMA_ENG_S2C 0x00000000 /**< DMA engine - S2C */ -#define DMA_ENG_TYPE_MASK 0x00000030 /**< DMA engine type */ -#define DMA_ENG_BLOCK 0x00000000 /**< DMA engine - Block type */ -#define DMA_ENG_PACKET 0x00000010 /**< DMA engine - Packet type */ -#define DMA_ENG_NUMBER 0x0000FF00 /**< DMA engine number */ -#define DMA_ENG_BD_MAX_BC 0x3F000000 /**< DMA engine max buffer size */ - - -/* Shift constants for selected masks */ -#define DMA_ENG_NUMBER_SHIFT 8 -#define DMA_ENG_BD_MAX_BC_SHIFT 24 - -/** @name Bitmasks of REG_DMA_ENG_CTRL_STATUS register. - * @{ - */ -/* Interrupt activity and acknowledgement bits */ -#define DMA_ENG_INT_ENABLE 0x00000001 /**< Enable interrupts */ -#define DMA_ENG_INT_DISABLE 0x00000000 /**< Disable interrupts */ -#define DMA_ENG_INT_ACTIVE_MASK 0x00000002 /**< Interrupt active? */ -#define DMA_ENG_INT_ACK 0x00000002 /**< Interrupt ack */ -#define DMA_ENG_INT_BDCOMP 0x00000004 /**< Int - BD completion */ -#define DMA_ENG_INT_BDCOMP_ACK 0x00000004 /**< Acknowledge */ -#define DMA_ENG_INT_ALERR 0x00000008 /**< Int - BD align error */ -#define DMA_ENG_INT_ALERR_ACK 0x00000008 /**< Acknowledge */ -#define DMA_ENG_INT_FETERR 0x00000010 /**< Int - BD fetch error */ -#define DMA_ENG_INT_FETERR_ACK 0x00000010 /**< Acknowledge */ -#define DMA_ENG_INT_ABORTERR 0x00000020 /**< Int - DMA abort error */ -#define DMA_ENG_INT_ABORTERR_ACK 0x00000020 /**< Acknowledge */ -#define DMA_ENG_INT_CHAINEND 0x00000080 /**< Int - BD chain ended */ -#define DMA_ENG_INT_CHAINEND_ACK 0x00000080 /**< Acknowledge */ - -/* DMA engine control */ -#define DMA_ENG_ENABLE_MASK 0x00000100 /**< DMA enabled? */ -#define DMA_ENG_ENABLE 0x00000100 /**< Enable DMA */ -#define DMA_ENG_DISABLE 0x00000000 /**< Disable DMA */ -#define DMA_ENG_STATE_MASK 0x00000C00 /**< Current DMA state? */ -#define DMA_ENG_RUNNING 0x00000400 /**< DMA running */ -#define DMA_ENG_IDLE 0x00000000 /**< DMA idle */ -#define DMA_ENG_WAITING 0x00000800 /**< DMA waiting */ -#define DMA_ENG_STATE_WAITED 0x00001000 /**< DMA waited earlier */ -#define DMA_ENG_WAITED_ACK 0x00001000 /**< Acknowledge */ -#define DMA_ENG_USER_RESET 0x00004000 /**< Reset only user logic */ -#define DMA_ENG_RESET 0x00008000 /**< Reset DMA engine + user */ - -#define DMA_ENG_ALLINT_MASK 0x000000BE /**< To get only int events */ - -#define DMA_ENGINE_PER_SIZE 0x100 /**< Separation between engine regs */ -#define DMA_OFFSET 0 /**< Starting register offset */ - /**< Size of DMA engine reg space */ -#define DMA_SIZE (MAX_DMA_ENGINES * DMA_ENGINE_PER_SIZE) - - -#define TX_CONFIG_ADDRESS 0x9108 /* Reg for controlling TX data */ -#define RX_CONFIG_ADDRESS 0x9100 /* Reg for controlling RX pkt generator */ -#define PKT_SIZE_ADDRESS 0x9104 /* Reg for programming packet size */ -#define STATUS_ADDRESS 0x910C /* Reg for checking TX pkt checker status */ - -/* Test start / stop conditions */ -#define PKTCHKR 0x00000001 /* Enable TX packet checker */ -#define PKTGENR 0x00000001 /* Enable RX packet generator */ -#define CHKR_MISMATCH 0x00000001 /* TX checker reported data mismatch */ -#define LOOPBACK 0x00000002 /* Enable TX data loopback onto RX */ |